Data Monitor
|
Monitored item |
(Unit) |
Remarks |
|
VSP SENSOR |
(km/h or mph) |
Displays the vehicle speed calculated from the CVT output shaft speed. |
|
ESTM VSP SIG |
(km/h or mph) |
Displays the vehicle speed signal (ABS) received through CAN communication. |
|
INPUT SPEED SENSOR |
(RPM) |
Displays the input speed calculated from the pulse signal of the input speed sensor. |
|
PRI SPEED SEN |
(RPM) |
Displays the primary pulley speed calculated from the pulse signal of the primary speed sensor. |
|
SEC REV SENSOR |
(RPM) |
Displays the secondary pulley speed calculated from the pulse signal of the output speed sensor. |
|
ENG SPEED SIG |
(RPM) |
Displays the engine speed received through CAN communication. |
|
SEC PRESSURE SEN |
(V) |
Displays the signal voltage of the secondary pressure sensor. |
|
PRI PRESSURE SEN |
(V) |
Displays the signal voltage of the primary pressure sensor. |
|
ATF TEMP SEN |
(V) |
Displays the signal voltage of the CVT fluid temperature sensor. |
|
G SENSOR |
(G) |
Displays the decel G signal received through CAN communication. |
|
VIGN SEN |
(V) |
Displays the battery voltage applied to TCM. |
|
PVING VOLT |
(V) |
Displays the backup voltage of TCM. |
|
VEHICLE SPEED |
(km/h or mph) |
Displays the vehicle speed recognized by TCM. |
|
INPUT REV |
(RPM) |
Displays the input shaft speed of CVT recognized by TCM. |
|
PRI SPEED |
(RPM) |
Displays the primary pulley speed recognized by TCM. |
|
SEC SPEED |
(RPM) |
Displays the secondary pulley speed recognized by TCM. |
|
ENG SPEED |
(RPM) |
Displays the engine speed recognized by TCM. |
|
SLIP REV |
(RPM) |
Displays the speed difference between the input shaft speed of CVT and the engine speed. |
|
PULLEY GEAR RATIO |
Displays the pulley gear ratio calculated from primary pulley speed/secondary pulley speed. |
|
|
G SPEED |
(G) |
Displays the acceleration and deceleration speed of the vehicle calculated from vehicle speed change. |
|
ACCEL POSI SEN 1 |
(deg) |
Displays the estimated throttle position received through CAN communication. |
|
VENG TRQ |
(Nm) |
Display the engine torque recognized by TCM. |
|
PRI TRQ |
(Nm) |
Display the input shaft torque of CVT. |
|
TRQ RTO |
Display the torque ratio of torque converter. |
|
|
SEC PRESSURE |
(MPa) |
Displays the secondary pressure calculated from the signal voltage of the secondary pressure sensor. |
|
PRI PRESSURE |
(MPa) |
Displays the primary pressure calculated from the signal voltage of the primary pressure sensor. |
|
FLUID TEMP |
(deg.C or deg.F) |
Displays the CVT fluid temperature calculated from the signal voltage of the CVT fluid temperature sensor. |
|
DSR REV |
(RPM) |
Displays the target primary pulley speed calculated from processing of gear shift control. |
|
TGT PLLY GR RATIO |
Displays the target gear ratio of the pulley from processing of gear shift control. |
|
|
LU PRS |
(MPa) |
Displays the target oil pressure of the torque converter clutch solenoid valve calculated from oil pressure processing of gear shift control. |
|
LINE PRS |
(MPa) |
Displays the target oil pressure of the line pressure solenoid valve calculated from oil pressure processing of gear shift control. |
|
TRGT PRI PRESSURE |
(MPa) |
Displays the target oil pressure of the primary pressure solenoid valve calculated from oil pressure processing of gear shift control. |
|
TRGT SELECT PRESSURE |
(MPa) |
Displays the target oil pressure of the select solenoid valve calculated from oil pressure processing of gear shift control. |
|
TRGT SEC PRESSURE |
(MPa) |
Displays the target oil pressure of the secondary pressure solenoid valve calculated from oil pressure processing of gear shift control. |
|
ISOLT1 |
(A) |
Displays the command current from TCM to the torque converter clutch solenoid valve. |
|
ISOLT2 |
(A) |
Displays the command current from TCM to the line pressure solenoid valve. |
|
PRI SOLENOID |
(A) |
Displays the command current from TCM to the primary pressure solenoid valve. |
|
SEC SOLENOID CURRENT |
(A) |
Displays the command current from TCM to the secondary pressure solenoid valve. |
|
SELECT SOLENOID CURRENT |
(A) |
Displays the command current from TCM to the select solenoid valve. |
|
SOLMON 1 |
(A) |
Monitors the command current from TCM to the torque converter clutch solenoid valve and displays the monitored value. |
|
SOLMON 2 |
(A) |
Monitors the command current from TCM to the line pressure solenoid valve and displays the monitored value. |
|
PRI SOL MON |
(A) |
Monitors the command current from TCM to the primary pressure solenoid valve and displays the monitored value. |
|
SEC SOL MON CURRENT |
(A) |
Monitors the command current from TCM to the secondary pressure solenoid valve and displays the monitored value. |
|
SELECT SOL MON CURRENT |
(A) |
Monitors the command current from TCM to the select solenoid valve and displays the monitored value. |
|
D POSITION SW |
(On/Off) |
Displays the operation status of the transmission range switch (D position). |
|
N POSITION SW |
(On/Off) |
Displays the operation status of the transmission range switch (N position). |
|
R POSITION SW |
(On/Off) |
Displays the operation status of the transmission range switch (R position). |
|
P POSITION SW |
(On/Off) |
Displays the operation status of the transmission range switch (P position). |
|
L POSITION SW |
(On/Off) |
Displays the operation status of the transmission range switch (L position). |
|
BRAKESW |
(On/Off) |
Displays the reception status of the stop lamp switch signal received through CAN communication. |
|
SPORT MODE SW |
(On/Off) |
Displays the reception status of the Ds mode switch signal received through CAN communication. |
|
ECO MODE SW |
(On/Off) |
Displays the reception status of the ECO mode switch signal received through CAN communication. |
|
STRDWNSW* |
(On/Off) |
Displays the operation status of the paddle shifter (down switch). |
|
STRUPSW* |
(On/Off) |
Displays the operation status of the paddle shifter (up switch). |
|
DOWNLVR* |
(On/Off) |
Displays the operation status of the selector lever (down switch). |
|
UPLVR* |
(On/Off) |
Displays the operation status of the selector lever (up switch). |
|
MMODE* |
(On/Off) |
Displays if the selector lever position is at the manual shift gate. |
|
SHIFT IND SIGNAL |
Displays the transaxle value of shift position signal transmitted via CAN communication. |
|
|
SPORT MODE IND |
(On/Off) |
Displays the transaxle status of the SPORT indicator lamp signal transmitted through CAN communication. |
|
MANU MODE SIGNAL |
(On/Off) |
Displays the transaxle status of the manual mode signal transmitted through CAN communication. |
|
DS RANGE SIGNAL |
(On/Off) |
Displays the Ds mode signal transmitted through CAN communication. |
|
VDC ON |
(On/Off) |
Displays the reception status of the VDC operation signal received through CAN communication. |
|
TCS ON |
(On/Off) |
Displays the reception status of the TCS operation signal received through CAN communication. |
|
ABS FAIL SIGNAL |
(On/Off) |
Displays the reception status of the ABS malfunction signal received through CAN communication. |
|
ABS ON |
(On/Off) |
Displays the reception status of the ABS operation signal received through CAN communication. |
|
RANGE |
Displays the gear position recognized by TCM. |
|
|
M GEAR POS |
Display the target gear of manual mode |
|
|
G SEN SLOPE |
(%) |
Displays the gradient angle calculated from the G sensor signal voltage. |
|
ENGBRKLVL |
(On/Off) |
Displays the setting of "ENGINE BRAKE ADJ" in "Work Support". |
|
G SEN CALIBRATION |
(YET/DONE) |
Displays the status of "G SENSOR CALIBRATION" in "Work Support". |
|
N IDLE STATUS* |
(On/Off) |
Displays idle neutral status. |
|
AXLE TYPE |
Displays the axle type of the vehicle. |
|
|
CVT-B |
|
|
|
CVT-A |
|
|
|
T/M warning indicator DTC |
Displays the first DTC when CVT system warning is displayed. |
|
|
T/M warning indicator mileage |
Displays the total mileage when CVT system warning is displayed at first time. |
|
*: Not applicable but displayed.