Active Test
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the DATA MONITOR. In response to instructions from CONSULT, instead of those from chassis control module on the vehicle, a drive signal is sent to the actuator to check its operation.
- Never perform ACTIVE TEST while driving the vehicle.
- Always bleed air from brake system before active test.
- Never perform active test when system is malfunctioning.
- When active test is performed while depressing the brake pedal, the brake pedal depressing stroke may change. This is not a malfunction.
- During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.
|
Test item |
Operation |
Description |
|
BRAKE ACTUATOR 1 MODE 1 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 1 MODE 2 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 1 MODE 3 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 2 MODE 1 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 2 MODE 2 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 2 MODE 3 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 3 MODE 1 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 3 MODE 2 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 3 MODE 3 |
Start |
Controls brake fluid pressure. |
|
Stop lamp OFF relay 1 active |
On |
If touching "On" with brake pedal depressed, the stop lamp turns OFF. |
|
Off |
Stops the drive of the relay. |
|
|
Stop lamp OFF relay 2 active |
On |
If touching "On" with the brake pedal depressed, other system becomes unable to input the signals of the brake pedal position switch. |
|
Off |
Stops the drive of the relay. |
|
|
MASTER WARNING ACTIVE |
On |
If touching "On" with the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute. |
|
Off |
The master warning lamp turns OFF. (vehicle in normal state) |
|
|
BRAKE HOLD DISP |
-- |
Displays but not used. |
|
FR TIRE DISP |
On |
Displays the front RH tire on the information display in the combination meter. |
|
Off |
Does not display the front RH tire on the information display in the combination meter. |
|
|
RR TIRE DISP |
On |
Displays the rear RH tire on the information display in the combination meter. |
|
Off |
Does not display the rear RH tire on the information display in the combination meter. |
|
|
FL TIRE DISP |
On |
Displays the front LH tire on the information display in the combination meter. |
|
Off |
Does not display the front LH tire on the information display in the combination meter. |
|
|
RL TIRE DISP |
On |
Displays the rear LH tire on the information display in the combination meter. |
|
Off |
Does not display the rear LH tire on the information display in the combination meter. |
|
|
VEHICLE DISP |
-- |
Displays but not used. |
|
INTERRUPT DISP |
-- |
Displays but not used. |
|
TURN DISP |
NO DISP |
Does not display the turning status on the information display in the combination meter. |
|
LH |
Displays the LH turning status on the information display in the combination meter. |
|
|
RH |
Displays the RH turning status on the information display in the combination meter. |
|
|
ATC 1 DISP |
On |
Displays the intelligent trace control function on the information display in the combination meter. |
|
Off |
Does not display the intelligent trace control function on the information display in the combination meter. |
|
|
ATC 2 DISP |
On |
Displays the intelligent trace control function on the information display in the combination meter. |
|
Off |
Does not display the intelligent trace control function on the information display in the combination meter. |
|
|
ATC 3 DISP |
On |
Displays the intelligent trace control function on the information display in the combination meter. |
|
Off |
Does not display the intelligent trace control function on the information display in the combination meter. |
|
|
ATC 4 DISP |
On |
Displays the intelligent trace control function on the information display in the combination meter. |
|
Off |
Does not display the intelligent trace control function on the information display in the combination meter. |
|
|
ATC 5 DISP |
On |
Displays the intelligent trace control function on the information display in the combination meter. |
|
Off |
Does not display the intelligent trace control function on the information display in the combination meter. |
|
|
Stop lamp ON relay active |
On |
When you touch the "On" without going through the brake pedal, stop lamp is turned ON. |
|
Off |
Stop the stop lamp ON relay. |