Data Monitor Mode

Monitored item

Unit

Description

Remarks

ENG SPEED

RPM

• Indicates the engine speed computed from the signal of the crankshaft position sensor and camshaft position sensor.

• Accuracy becomes poor if engine speed drops below the idle RPM.
• If the signal is interrupted while the engine is running, an abnormal value may be indicated.

MAS A/F SE-B1

V

• The signal voltage of the mass air flow sensor is displayed.

• When the engine is stopped, a certain value is indicated.
• When engine is running, specification range is indicated in "SPEC".

B/FUEL SCHDL

ms

• "Base fuel schedule" indicates the fuel injection pulse width programmed into ECM, prior to any learned on board correction.

• When engine is running, specification range is indicated in "SPEC".

A/F ALPHA-B1

%

• The mean value of the air-fuel ratio feedback correction factor per cycle is indicated.

• When the engine is stopped, a certain value is indicated.
• This data also includes the data for the air-fuel ratio learning control.
• When engine is running, specification range is indicated in "SPEC".

A/F ALPHA-B2

COOLAN TEMP/S

deg. C or deg. F

• The engine coolant temperature (determined by the signal voltage of the engine coolant temperature sensor 1) is displayed.

• When the engine coolant temperature sensor 1 is open or short-circuited, ECM enters fail-safe mode. The engine coolant temperature determined by the ECM is displayed.

A/F SEN1 (B1)

V

• The A/F signal computed from the input signal of the air fuel ratio (A/F) sensor 1 is displayed.

A/F SEN1 (B2)

HO2S2 (B1)

V

• The signal voltage of the heated oxygen sensor 2 is displayed.

HO2S2 (B2)

HO2S2 MNTR (B1)

RICH/LEAN

• Display of heated oxygen sensor 2 signal:

  RICH: means the amount of oxygen after three way catalyst is relatively small.

  LEAN: means the amount of oxygen after three way catalyst is relatively large.

• When the engine is stopped, a certain value is indicated.

HO2S2 MNTR (B2)

VHCL SPEED SE

km/h or mph

• The vehicle speed computed from the vehicle speed signal sent from combination meter is displayed.

BATTERY VOLT

V

• The power supply voltage of ECM is displayed.

ACCEL SEN 1

V

• The accelerator pedal position sensor signal voltage is displayed.

• ACCEL SEN 2 signal is converted by ECM internally. Thus, they differs from ECM terminal voltage signal.

ACCEL SEN 2

TP SEN 1-B1

V

• The throttle position sensor signal voltage is displayed.

• TP SEN 2-B1 signal is converted by ECM internally. Thus, they differs from ECM terminal voltage signal.

TP SEN 2-B1

FUEL T/TMP SE

deg. C or deg. F

• The fuel temperature (determined by the signal voltage of the fuel tank temperature sensor) is displayed.

FUEL PUMP RLY

ON/OFF

Indicates the fuel pump relay control condition determined by ECM according to the input signals.

EVAP SYS PRES

V

• The signal voltage of EVAP control system pressure sensor is displayed.

SET LAMP

ON/OFF

• Indicates [ON/OFF] condition of SET lamp determined by the ECM according to the input signals.

AT OD CANCEL

ON/OFF

Indicates [ON/OFF] condition of A/T O/D cancel signal sent from the TCM.

• For M/T models always "OFF" is displayed.

AT OD MONITOR

ON/OFF

Indicates [ON/OFF] condition of A/T O/D according to the input signal from the TCM.

• For M/T models always "OFF" is displayed.

LO SPEED CUT

NON/CUT

• Indicates the vehicle cruise condition.

  NON: Vehicle speed is maintained at the ASCD set speed.

  CUT: Vehicle speed decreased to excessively low compared with the ASCD set speed, and ASCD operation is cut off.

VHCL SPD CUT

NON/CUT

• Indicates the vehicle cruise condition.

  NON: Vehicle speed is maintained at the ASCD set speed.

  CUT: Vehicle speed increased to excessively high compared with the ASCD set speed, and ASCD operation is cut off.

SET VHCL SPD

km/h or mph

• The preset vehicle speed is displayed.

VTC DTY EX B1

%

• The control value of the exhaust valve timing control solenoid valve (determined by ECM according to the input signals) is indicated.
• The advance angle becomes larger as the value increases.

VTC DTY EX B2

FUEL LEVEL SE

V

• The signal voltage of the fuel level sensor is displayed.

START SIGNAL

ON/OFF

• Indicates start signal status [ON/OFF] computed by the ECM according to the signals of engine speed and battery voltage.

• After starting the engine, [OFF] is displayed regardless of the starter signal.

CLSD THL POS

ON/OFF

• Indicates idle position [ON/OFF] computed by ECM according to the accelerator pedal position sensor signal.

AIR COND SIG

ON/OFF

• Indicates [ON/OFF] condition of the air conditioner switch as determined by the air conditioner signal.

PW/ST SIGNAL

ON/OFF

• [ON/OFF] condition of the power steering system (determined by the signal voltage of the power steering pressure sensor signal) is indicated.

LOAD SIGNAL

ON/OFF

• Indicates [ON/OFF] condition from the electrical load signal.

  ON: Rear window defogger switch is ON and/or lighting switch is in 2nd position.

  OFF: Both rear window defogger switch and lighting switch are OFF.

IGNITION SW

ON/OFF

• Indicates [ON/OFF] condition from ignition switch signal.

HEATER FAN SW

ON/OFF

• Indicates [ON/OFF] condition from the blower fan ON signal.

BRAKE SW

ON/OFF

• Indicates [ON/OFF] condition from the stop lamp switch signal.

IGN TIMING

BTDC

• Indicates the ignition timing computed by ECM according to the input signals.

• When the engine is stopped, a certain value is indicated.

COMBUSTION

--

• These items are displayed but are not applicable to this model.

CAL/LD VALUE

%

• "Calculated load value" indicates the value of the current air flow divided by peak air flow.

MASS AIRFLOW

g/s

• Indicates the mass air flow computed by ECM according to the signal voltage of the mass air flow sensor.

PURG VOL C/V

%

• Indicates the EVAP canister purge volume control solenoid valve control value computed by the ECM according to the input signals.
• The opening becomes larger as the value increases.

INT/V SOL (B1)

%

• The control value of the intake valve timing control solenoid valve (determined by ECM according to the input signals) is indicated.
• The advance angle becomes larger as the value increases.

INT/V SOL (B2)

AIR COND RLY

ON/OFF

• The air conditioner relay control condition (determined by ECM according to the input signals) is indicated.

VENT CONT/V

ON/OFF

• The control condition of the EVAP canister vent control valve (determined by ECM according to the input signals) is indicated.

  ON: Closed

  OFF: Open

THRTL RELAY

ON/OFF

• Indicates the throttle control motor relay control condition determined by the ECM according to the input signals.

A/F S1 HTR (B1)

%

• Air fuel ratio (A/F) sensor 1 heater control value computed by ECM according to the input signals.
• The current flow to the heater becomes larger as the value increases.

A/F S1 HTR (B2)

HO2S2 HTR (B1)

ON/OFF

• Indicates [ON/OFF] condition of heated oxygen sensor 2 heater determined by ECM according to the input signals.

HO2S2 HTR (B2)

ALT DUTY SIG

ON/OFF

• The control condition of the power generation voltage variable control (determined by ECM according to the input signals) is indicated.

  ON: Power generation voltage variable control is active.

  OFF: Power generation voltage variable control is inactive.

I/P PULLY SPD

RPM

• Indicates the engine speed computed from the input speed sensor signal.

VEHICLE SPEED

km/h or mph

• The vehicle speed computed from the vehicle speed signal sent from TCM is displayed.

IDL A/V LEARN

YET/CMPLT

• Displays the condition of Idle Air Volume Learning

  YET: Idle air volume learning has not been performed yet.

  CMPLT: Idle air volume learning has already been performed successfully.

TRVL AFTER MIL

km or mile

• Distance traveled while MIL is activated.

SNOW MODE SW

ON/OFF

• Indicates [ON/OFF] condition from the snow mode switch signal.

ENG OIL TEMP

deg. C or deg. F

• The engine oil temperature (determined by the signal voltage of the engine oil temperature sensor) is displayed.

MAIN SW

ON/OFF

• Indicates [ON/OFF] condition from MAIN switch signal.

CANCEL SW

ON/OFF

• Indicates [ON/OFF] condition from CANCEL switch signal.

RESUME/ACC SW

ON/OFF

• Indicates [ON/OFF] condition from ACCELERATE/RESUME switch signal.

SET SW

ON/OFF

• Indicates [ON/OFF] condition from COAST/SET switch signal.

BRAKE SW1

ON/OFF

• Indicates [ON/OFF] condition from brake pedal position switch signal.

BRAKE SW2

ON/OFF

• Indicates [ON/OFF] condition of stop lamp switch signal.

DIST SW

ON/OFF

• Indicates [ON/OFF] condition from DISTANCE switch signal.

CRUISE LAMP

ON/OFF

• Indicates [ON/OFF] condition of CRUISE indicator determined by the ECM according to the input signals.

AC EVA TEMP

deg. C or deg. F

• Indicates A/C evaporator temperature sent from A/C auto amp.

AC EVA TARGET

deg. C or deg. F

• Indicates target A/C evaporator temperature sent from A/C auto amp.

FAN DUTY

%

• Indicates a command value for cooling fan. The value is calculated by ECM based on input signals.

ALT DUTY

%

• Indicates the duty ratio of the power generation command value. The ratio is calculated by ECM based on the battery current sensor signal.

BAT CUR SEN

mV

• The signal voltage of battery current sensor is displayed.

A/F ADJ-B1

--

• Indicates the correction of a factor stored in ECM. The factor is calculated from the difference between the target air-fuel ratio stored in ECM and the air-fuel ratio calculated from A/F sensor 1 signal.

A/F ADJ-B2

P/N POSI SW

ON/OFF

• Indicates [ON/OFF] condition from the park/neutral position (PNP) signal.

INT/A TEMP SE

deg. C or deg. F

• The intake air temperature (determined by the signal voltage of the intake air temperature sensor) is indicated.

AC PRESS SEN

V

• The signal voltage from the refrigerant pressure sensor is displayed.

FUEL PRES SEN

MPa

• Indicates the fuel rail pressure computed by ECM according to the input signals

FUEL INJ B1

msec

• ECM-calculated injection pulse width of the fuel injector on the Bank 1 side.

FUEL INJ B2

msec

• ECM-calculated injection pulse width of the fuel injector on the Bank 2 side.

INT/V TIM (B1)

deg. CA

• Indicates [ deg. CA] of intake camshaft advance angle.

INT/V TIM (B2)

MAP SENSOR

V

• The signal voltage from the manifold absolute pressure (MAP) sensor is displayed.

EVAP LEAK DIAG

YET/CMPLT

• Indicates the condition of EVAP leak diagnosis.

  YET: EVAP leak diagnosis has not been performed yet.

  CMPLT: EVAP leak diagnosis has been performed successfully.

EVAP DIAG READY

ON/OFF

• Indicates the ready condition of EVAP leak diagnosis.

  ON: Diagnosis has been ready condition.

  OFF: Diagnosis has not been ready condition.

VVEL LEARN

YET/DONE

• Display the condition of VVEL learning

  YET: VVEL learning has not been performed yet.

  DONE: VVEL learning has already been performed successfully.

VVEL SEN LEARN-B1

V

• Indicates the VVEL learning value.

VVEL SEN LEARN-B2

VVEL POSITION SEN-B1

V

• The VVEL control shaft position sensor signal voltage is displayed.

VVEL POSITION SEN-B2

VVEL TIM-B1

deg

• Indicates [deg] of VVEL control shaft angle.

VVEL TIM-B2

FPCM

HI/MID/LOW/OFF

• The control condition of the fuel pump control module (FPCM) (determined by ECM according to the input signals) is indicated.

BAT TEMP SEN

V

• The signal voltage from the battery temperature sensor is displayed.

COOLING FAN SPD

RPM

• Displays a cooling fan speed from a signal of fan clutch assembly.

THRTL STK CNT B1 ^*

--

--

HO2 S2 DIAG1(B1)

INCMP/CMPLT

• Indicates DTC P0139 self-diagnosis (delayed response) condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

HO2 S2 DIAG1(B2)

INCMP/CMPLT

• Indicates DTC P0159 self-diagnosis (delayed response) condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

HO2 S2 DIAG2(B1)

INCMP/CMPLT

• Indicates DTC P0139 self-diagnosis (slow response) condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

HO2 S2 DIAG2(B2)

INCMP/CMPLT

• Indicates DTC P0159 self-diagnosis (slow response) condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

FUEL INJ TIMG

deg

• Indicates the fuel injection timing computed by ECM according to the input signals.

H/P FUEL PUMP DEG

deg

• Displays ECM-calculated fuel discharge position of the high pressure fuel pump.

FUEL PRES SEN V

mV

• The signal voltage of FRP sensor is displayed.

L/FUEL PRES SEN

MPa

• Displays a pressure value calculated from a low fuel pressure sensor voltage.

L/FUEL PRES SEN V

mV

• The signal voltage of low fuel pressure sensor is displayed.

ECM TEMP 1

deg. C or deg. F

• Displays a temperature calculated from a signal of ECM temperature sensor 1.

ECM TEMP 2

deg. C or deg. F

• Displays a temperature calculated from a signal of ECM temperature sensor 2.

FUEL PUMP DUTY

%

• The control condition of the fuel pump control module (FPCM) (determined by ECM according to the input signals) is indicated.

A/F SEN1 DIAG1 (B1)

INCMP/CMPLT

• Indicates DTC P015A or P015B self-diagnosis condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG1 (B2)

INCMP/CMPLT

• Indicates DTC P015C or P015D self-diagnosis condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG2 (B1)

INCMP/CMPLT

• Indicates DTC P014C or P014D self-diagnosis condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG2 (B2)

INCMP/CMPLT

• Indicates DTC P014E or P014F self-diagnosis condition.

  INCMP: Self-diagnosis is incomplete.

  CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG3 (B1)

ABSNT/PRSNT

• Indicates DTC P014C, P014D, P015A or P015B self-diagnosis condition.

  ABSNT: The vehicle condition is not within the diagnosis range.

  PRSNT: The vehicle condition is within the diagnosis range.

A/F SEN1 DIAG3 (B2)

ABSNT/PRSNT

• Indicates DTC P014E, P014F, P015C or P015D self-diagnosis condition.

  ABSNT: The vehicle condition is not within the diagnosis range.

  PRSNT: The vehicle condition is within the diagnosis range.

SYSTEM 1 DIAGNOSIS A B1

INCMP/CMPLT

• Indicates DTC P219A self-diagnosis condition.
  • INCMP: Self-diagnosis is incomplete.
  • CMPLT: Self-diagnosis is complete.

SYSTEM 1 DIAGNOSIS A B2

INCMP/CMPLT

• Indicates DTC P219B self-diagnosis condition.
  • INCMP: Self-diagnosis is incomplete.
  • CMPLT: Self-diagnosis is complete.

SYSTEM 1 DIAGNOSIS B B1

ABSNT/PRSNT

• Indicates DTC P219A self-diagnosis condition.
  • ABSNT: Self-diagnosis standby
  • PRSNT: Under self-diagnosis

SYSTEM 1 DIAGNOSIS B B2

ABSNT/PRSNT

• Indicates DTC P219B self-diagnosis condition.
  • ABSNT: Self-diagnosis standby
  • PRSNT: Under self-diagnosis

A/F-S ATMSPHRC CRCT B1

--

• Displays a determined value of atmospheric correction factor necessary for correcting an A/F sensor signal input to ECM. The signal used for the correction is an A/F sensor signal transmitted while driving under atmospheric pressure.

A/F-S ATMSPHRC CRCT B2

--

• Displays a determined value of atmospheric correction factor necessary for correcting an A/F sensor signal input to ECM. The signal used for the correction is an A/F sensor signal transmitted while driving under atmospheric pressure.

A/F-S ATMSPHRC CRCT UP B1

count

• Displays the number of updates of the A/F sensor atmospheric correction factor.

A/F-S ATMSPHRC CRCT UP B2

count

• Displays the number of updates of the A/F sensor atmospheric correction factor.

EXH/V TIM B1

deg. CA

• Indicates [ deg. CA] of exhaust camshaft retard angle.

EXH/V TIM B2

EXH V/T LEARN

YET/CMPLT

• Display the condition of Exhaust Valve Timing Control Learning

  YET: Exhaust Valve Timing Control Learning has not been performed yet.

  CMPLT: Exhaust Valve Timing Control Learning has already been performed successfully.

EXHAUST GAS TEMP SEN 1 B1

mV

• The signal voltage of exhaust gas temperature sensor (bank 1) is displayed.

EXHAUST GAS TEMP SEN 1 B2

mV

• The signal voltage of exhaust gas temperature sensor (bank 2) is displayed.

EOP SENSOR

mV

• The signal voltage of engine oil pressure sensor is displayed.

RADIATOR COOLANT TEMP

deg. C or deg. F

Description: The radiator coolant temperature (determined by the signal voltage of the radiator coolant temperature sensor) is displayed.

ENGINE COOLANT B/V POSI

deg

Description: The Multi-way Control Valve position detected by the position sensor is displayed.

A/F IMBALNC DIAG-CPS STAT

ABSNT/PRSNT

• Indicates DTC P219C - P219F and P21A0 - P21A3 self-diagnosis condition.

  ABSNT: The vehicle condition is not within the diagnosis range.

  PRSNT: The vehicle condition is within the diagnosis range.

A/F IMBALNC DIAG-CPS CMPLT

INCMP/CMPLT

• Indicates DTC P219C - P219F and P21A0 - P21A3 self-diagnosis condition.
  • INCMP: Self-diagnosis is incomplete.
  • CMPLT: Self-diagnosis is complete.

A/GRLL SHTTR POSITION

F/CLOSE

MOVING

F/OPEN

UNIDTF

Indicates the status of active grille shutter.

• F/CLOSE: Active grille shutter is fully closed.
• MOVING: Active grille shutter is in motion.
• F/OPEN: Active grille shutter is fully opened.
• UNIDTF: Unable to specify the shutter position.

A/GRLL SHTTR CALIBRATION

INCMP/CMPLT

• Indicates initial position learning status of active grille shutter.
  • CMPLT: The leaning is complete.
  • INCOMP: The learning is incomplete.

A/GRLL SHTTR CIRCUIT DIAG

OK/NG

• Indicates the diagnosis result of active grille shutter circuit.
  • OK: Normal.
  • NG: Malfunction detected.

A/GRLL SHTTR TEMP DIAG

OK/NG

• Indicates the diagnosis result of active grille shutter actuator temperature status.
  • OK: Normal
  • NG: Abnormal temperature detected.

A/GRLL SHTTR VOLT DIAG

OK/NG

• Indicates the diagnosis result of active grille shutter actuator voltage status.
  • OK: Normal
  • NG: Abnormal temperature detected.

A/GRLL SHTTR OVER RUN

OK/NG

• Indicates active grille shutter moves beyond normal moving limit.
  • OK: Normal
  • NG: Malfunction detected.

A/GRLL SHTTR STUCK

OK/NG

• Indicates the diagnosis result of active grille shutter stuck or the operation range less than normal.
  • OK: Normal
  • NG: Malfunction detected.

A/GRLL SHTTR CALIB DIAG

OK/NG

• Indicates the diagnosis result of initial position learning of active grille shutter.
  • OK: Normal
  • NG: Deficiency detected.