LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2012 >> Matrix Base, Standard Trans >> Repair and Diagnosis (Single Page) >> External Pages >> Different car >> Section 55 (Air Conditioning System (Service Information)) >> Blower Unit >> Installation >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Blower Unit: Installation: Installation

WARNING: This page is about a different car, the 2011 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL BLOWER ASSEMBLY (w/o PTC Heater) 
    1. Install the blower assembly with the 3 screws.
      Fig 1: Locating Blower Assembly And Screws
      GTY207480Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for Automatic Air Conditioning System:
      1. Connect the connector.
  2. INSTALL BLOWER ASSEMBLY (w/ PTC Heater) 
    1. Install the blower assembly with the 3 screws.
      Fig 2: Locating Blower Assembly And Screws
      GTY167404Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the quick heater connector and install the screw.
    3. for Automatic Air Conditioning System:
      1. Connect the connector.
    4. Engage each clamp.
      Fig 3: Identifying Blower Assembly Clamp
      GTY187814Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY  See step  3
  4. TEMPORARILY TIGHTEN AIR CONDITIONING UNIT  See step  4
  5. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY (for Manual Air Conditioning System)  See step  5
  6. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY (for Automatic Air Conditioning System)  See step  6
  7. INSTALL AIR CONDITIONING UNIT  See step  7
  8. INSTALL REAR NO. 1 AIR DUCT (w/ Rear Air Duct)  See step  9
  9. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY  See step  10
  10. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for Manual Air Conditioning System)  See step  11
  11. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for Automatic Air Conditioning System)  See step  12
  12. INSTALL REAR NO. 3 AIR DUCT (w/ Rear Air Duct)  See step  13
  13. INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)  See step  14
  14. INSTALL CENTER INSTRUMENT PANEL TO COWL BRACE  See step  15
  15. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY  See step  16
  16. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY  See step  17
  17. INSTALL SMART KEY ECU ASSEMBLY (w/ Smart Key System)  . Refer to INSTALLATION - Step 1
  18. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY  . Refer to INSTALLATION - Step 1
  19. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY  . Refer to INSTALLATION - Step 1
  20. INSTALL CONSOLE BOX ASSEMBLY (for Manual Transaxle)  . Refer to INSTALLATION - Step 2
  21. INSTALL CONSOLE BOX ASSEMBLY (for Automatic Transaxle)  . Refer to INSTALLATION - Step 1
  22. INSTALL CONSOLE BOX CARPET  . Refer to INSTALLATION - Step 3
  23. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY  . Refer to INSTALLATION - Step 5
  24. INSTALL NO. 1 SWITCH HOLE BASE (w/o Smart Key System)  . Refer to INSTALLATION - Step 7
  25. INSTALL NO. 1 SWITCH HOLE BASE (w/ Smart Key System)  . Refer to INSTALLATION - Step 8
  26. INSTALL FRONT NO. 1 CONSOLE BOX INSERT  . Refer to INSTALLATION - Step 10
  27. INSTALL COWL SIDE TRIM BOARD LH  . Refer to INSTALLATION - Step 53
  28. INSTALL FRONT DOOR SCUFF PLATE LH  . Refer to INSTALLATION - Step 54
  29. INSTALL FRONT NO. 2 CONSOLE BOX INSERT  . Refer to INSTALLATION - Step 13
  30. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)  . Refer to INSTALLATION - Step 14
  31. INSTALL COWL SIDE TRIM BOARD RH  . Refer to INSTALLATION - Step 57
  32. INSTALL FRONT DOOR SCUFF PLATE RH  . Refer to INSTALLATION - Step 58
  33. INSTALL AIR CONDITIONING PANEL ASSEMBLY (for Manual Air Conditioning System)  . Refer to INSTALLATION - Step 1
  34. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)  . Refer to INSTALLATION - Step 1
  35. INSTALL INSTRUMENT PANEL HOLE COVER  . Refer to INSTALLATION - Step 19
  36. INSTALL INSTRUMENT PANEL BOX ASSEMBLY  . Refer to INSTALLATION - Step 20
  37. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Manual Transaxle)  . Refer to INSTALLATION - Step 21
  38. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Automatic Transaxle)  . Refer to INSTALLATION - Step 22
  39. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)  . Refer to INSTALLATION - Step 23
  40. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)  . Refer to INSTALLATION - Step 24
  41. INSTALL RADIO RECEIVER WITH BRACKET (w/o Navigation System)  . Refer to INSTALLATION - Step 4
  42. INSTALL NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)  . Refer to INSTALLATION - Step 4
  43. INSTALL STEERING POST ASSEMBLY (for 2ZR-FE)  . Refer to INSTALLATION - Step 2
  44. INSTALL STEERING POST ASSEMBLY (for 2AZ-FE)  . Refer to INSTALLATION - Step 3
  45. TURN FRONT WHEELS FACING STRAIGHT AHEAD 
  46. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY  . Refer to INSTALLATION - Step 5
  47. INSTALL STOP LIGHT SWITCH ASSEMBLY  . Refer to INSTALLATION - Step 1
  48. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY  . Refer to INSTALLATION - Step 7
  49. INSTALL INSTRUMENT PANEL SUB REINFORCEMENT  . Refer to INSTALLATION - Step 8
  50. INSTALL COLUMN HOLE COVER SILENCER SHEET  . Refer to INSTALLATION - Step 9
  51. INSTALL TRANSPONDER KEY AMPLIFIER (w/o Smart Key System)  . Refer to INSTALLATION - Step 10
  52. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY  . Refer to INSTALLATION - Step 12
  53. INSTALL UPPER STEERING COLUMN COVER  . Refer to INSTALLATION - Step 13
  54. INSTALL LOWER STEERING COLUMN COVER  . Refer to INSTALLATION - Step 14
  55. TURN FRONT WHEELS FACING STRAIGHT AHEAD 
  56. ADJUST SPIRAL CABLE  . Refer to INSTALLATION - Step 7
  57. INSTALL STEERING WHEEL ASSEMBLY (w/o Front Spoiler) 

    Refer to INSTALLATION

  58. INSTALL STEERING WHEEL ASSEMBLY (w/ Front Spoiler) 

    Refer to INSTALLATION

  59. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY  . Refer to INSTALLATION - Step 9
  60. INSTALL POWER STEERING ECU ASSEMBLY (for 2ZR-FE)  . Refer to INSTALLATION - Step 2
  61. INSTALL POWER STEERING ECU ASSEMBLY (for 2AZ-FE)  . Refer to INSTALLATION - Step 2
  62. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY  . Refer to INSTALLATION - Step 1
  63. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY  . Refer to INSTALLATION - Step 7
  64. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH  . Refer to INSTALLATION - Step 52
  65. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY  . Refer to INSTALLATION - Step 4
  66. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH  . Refer to INSTALLATION - Step 56
  67. INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY  . Refer to INSTALLATION - Step 6
  68. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY  . Refer to INSTALLATION - Step 7
  69. INSTALL FRONT PILLAR GARNISH LH  . Refer to INSTALLATION - Step 61
  70. INSTALL FRONT PILLAR GARNISH RH  . Refer to INSTALLATION - Step 62
  71. INSTALL COMBINATION METER ASSEMBLY  . Refer to INSTALLATION - Step 1
  72. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY  . Refer to INSTALLATION - Step 2
  73. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY  . Refer to INSTALLATION - Step 12
  74. INSTALL INSTRUMENT PANEL FINISH PANEL END LH  . Refer to INSTALLATION - Step 13
  75. INSTALL INSTRUMENT PANEL FINISH PANEL END RH  . Refer to INSTALLATION - Step 14
  76. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH  . Refer to INSTALLATION - Step 15
  77. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH  . Refer to INSTALLATION - Step 16
  78. INSTALL HEATER OUTLET WATER HOSE  See step  79
  79. INSTALL HEATER INLET WATER HOSE  See step  80
  80. INSTALL AIR CONDITIONING TUBE ASSEMBLY  See step  81
  81. INSTALL SUCTION PIPE SUB-ASSEMBLY  See step  82
  82. INSTALL OUTER COWL TOP PANEL (for TMC Made)  . Refer to INSTALLATION - Step 13
  83. INSTALL OUTER COWL TOP PANEL (except TMC Made)  . Refer to INSTALLATION - Step 14
  84. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY  . Refer to INSTALLATION - Step 3
  85. INSTALL COWL TOP VENTILATOR LOUVER LH  . Refer to INSTALLATION - Step 4
  86. INSTALL CENTER NO. 1 COWL TOP VENTILATOR LOUVER  . Refer to INSTALLATION - Step 5
  87. INSTALL HOOD TO COWL TOP SEAL  . Refer to INSTALLATION - Step 6
  88. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH  . Refer to INSTALLATION - Step 7
  89. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH  . Refer to INSTALLATION - Step 8
  90. INSTALL FRONT WIPER ARM HEAD CAP  . Refer to INSTALLATION - Step 9
  91. CHARGE WITH REFRIGERANT  See step  2
  92. ADD ENGINE COOLANT (for 2ZR-FE)  . Refer to REPLACEMENT - Step 2
  93. ADD ENGINE COOLANT (for 2AZ-FE)  . Refer to REPLACEMENT - Step 2
  94. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  95. INSPECT FOR COOLANT LEAK (for 2ZR-FE)  . Refer to ON-VEHICLE INSPECTION - Step 1
  96. INSPECT FOR COOLANT LEAK (for 2AZ-FE)  . Refer to ON-VEHICLE INSPECTION - Step 1
  97. INSPECT STEERING PAD  . Refer to INSTALLATION - Step 8
  98. INSPECT SRS WARNING LIGHT 

    Refer to DIAGNOSIS SYSTEM

  99. WARM UP ENGINE  See step  3
  100. INSPECT FOR REFRIGERANT LEAK  See step  4
scientia non olet · About LEMON Manuals