LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Dodge and Ram >> 1994 >> Intrepid Base, 3.3 T >> Repair and Diagnosis >> External Pages >> Different car >> Section 13 (Engine Controls - Tests W/Codes - Body Control Computer (Convert)) >> Self-Diagnostic Tests >> Test 1A - Identifying Vehicle Equipment & System Problems
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test 1A - Identifying Vehicle Equipment & System Problems

WARNING: This page is about a different car, the 1994 Chrysler LeBaron. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: For connector terminal identification, see CONNECTOR  IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS  . When directed to go to next step, disregard step if vehicle is not equipped with module being tested.
  1. Connect DRB to Chrysler Collision Detection (CCD) DATA LINK CONNECTOR (DLC). DLC is located under dash to left of steering column. Turn ignition switch to ON position. Using DRB, select BODY SYSTEM.
  2. If DRB does not display BUS OPERATIONAL, see VEHICLE COMMUNICATIONS. If DRB displays BUS OPERATIONAL, go to next step.
  3. Using DRB, select body controller. If DRB displays NO RESPONSE, go to TEST 69A  . If DRB does not display NO RESPONSE, go to next step.
  4. Using DRB, select electronic cluster, if equipped. If DRB displays NO RESPONSE, go to TEST 70A  . If DRB does not display NO RESPONSE, go to next step.
  5. Using DRB, select Electronic Vehicle Information Center (EVIC), if equipped. If DRB displays NO RESPONSE, go to TEST 71A. If DRB does not display NO RESPONSE, go to next step.
  6. Using DRB, select traveler, if equipped. If DRB displays NO RESPONSE, go to TEST 72A  . If DRB does not display NO RESPONSE, go to next step.
  7. Using DRB, select compass temperature, if equipped. If DRB displays NO RESPONSE, go to TEST 73A  . If DRB does not display NO RESPONSE, go to next step.
  8. Using DRB, select engine node, if equipped. If DRB displays NO RESPONSE, go to TEST 74A  . If DRB does not display NO RESPONSE, go to next step.
  9. Using DRB, select PCM monitor. If DRB displays NO RESPONSE, go to TEST 75A  . If DRB does not display NO RESPONSE, go to next step.
    NOTE: Perform TEST VER-1 after each repair.
  10. Using DRB, read trouble codes. If DRB does not display trouble codes, see DIAGNOSTIC TEST DIRECTORY  table for specific diagnosis. If DRB displays trouble codes, go to next step.
  11. If DRB displays NO VOLTAGE AT PIN 16 OF BODY COMPUTER, go to TEST 69A. If DRB does not display NO VOLTAGE AT PIN 16 OF BODY COMPUTER, go to next step.
  12. If DRB displays EEPROM CHECKSUM FAILURE, replace Body Control Module (BCM). If DRB does not display EEPROM CHECKSUM FAILURE, go to next step.
  13. If DRB displays ODOMETER TEST FAILURE, replace BCM. If DRB does not display ODOMETER TEST FAILURE, go to next step.
  14. If DRB displays WRONG BODY COMPUTER, install correct BCM. If DRB does not display WRONG BODY COMPUTER, proceed to DIAGNOSTIC TEST DIRECTORY for specific diagnosis.
DIAGNOSTIC TEST DIRECTORY

Problem/Message Perform Test
EVIC Panel Blank 2A 
Message On The EVIC Panel 3A 
Missing Message On The EVIC 3A 
EVIC Panel Switches 31A 
EVIC Panel Switch Function 31A 
EVIC Panel Illumination 40A 
Electronic Instrument Cluster 32A 
Door Lock System 41A 
Intermittent Wiper System 43A 
Illuminated Entry System 46A 
Courtesy Lamp System 47A 
Traveler Module 52A 
Compass/Temp Module 55A 
Key-In Lamp 57A 
Headlamp Time Delay Will Not Work 58A 
Mechanical Cluster Warning Lamp 59A 
Chime Functions 63A 
scientia non olet · About LEMON Manuals