Climate Control System DTCS
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B1081:07 | Left Temperature Damper Motor: Mechanical Failures | GO to Pinpoint Test K |
| B1081:11 | Left Temperature Damper Motor: Circuit Short To Ground | GO to Pinpoint Test K |
| B1081:12 | Left Temperature Damper Motor: Circuit Short To Battery | GO to Pinpoint Test K |
| B1081:13 | Left Temperature Damper Motor: Circuit Open | GO to Pinpoint Test K |
| B10AF:11 | Blower Fan Relay: Circuit Short To Ground | GO to Pinpoint Test L |
| B10AF:12 | Blower Fan Relay: Circuit Short To Battery | GO to Pinpoint Test M |
| B10AF:13 | Blower Fan Relay: Circuit Open | GO to Pinpoint Test L |
| B10B8:63 | Push Buttons: Circuit / Component Protection Time-Out | GO to Pinpoint Test AC |
| B10B9:12 | Blower Control: Circuit Short To Battery | GO to Pinpoint Test L |
| B10B9:14 | Blower Control: Circuit Short To Ground Or Open | GO to Pinpoint Test L |
| B10B9:14 | Blower Control: Circuit Short To Ground Or Open | GO to Pinpoint Test M |
| B10EA:12 | Positive temperature coefficient heater: Circuit Short To Battery | GO to Pinpoint Test A |
| B10EA:14 | Positive temperature coefficient heater: Circuit Short To Ground Or Open | GO to Pinpoint Test A |
| B11E5:11 | Left HVAC Damper Position Sensor: Circuit Short To Ground | GO to Pinpoint Test K |
| B11E5:15 | Left HVAC Damper Position Sensor: Circuit Short To Battery Or Open | GO to Pinpoint Test K |
| B12CA:11 | Start/Stop "Eco-Start" Status Indicator: Circuit Short To Ground | GO to Pinpoint Test AD |
| B12CA:15 | Start/Stop "Eco-Start" Status Indicator: Circuit Short To Battery or Open | GO to Pinpoint Test AD |
| B1B71:11 | Evaporator Temperature Sensor: Circuit Short To Ground | GO to Pinpoint Test D |
| B1B71:15 | Evaporator Temperature Sensor: Circuit Short To Battery Or Open | GO to Pinpoint Test D |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test V |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test W |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub-Type Information | GO to Pinpoint Test X |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test Y |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub-Type Information | GO to Pinpoint Test S |
| U0401:82 | Invalid Data Received from ECM/PCM A: Alive / Sequence Counter Incorrect / Not Updated | GO to Pinpoint Test S |
| U0422:68 | Invalid Data Received From Body Control Module: Event Information | GO to Pinpoint Test S |
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | GO to Pinpoint Test S |
| U1000:00 | Solid State Driver Protection Active -Driver Disabled: No Sub Type Information | GO to Pinpoint Test Z |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test T |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test T |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test T |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test T |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test U |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AA |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AB |
| P0532:00 | A/C Refrigerant Pressure Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| P0533:00 | A/C Refrigerant Pressure Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test B |
| P0645:00 | A/C Clutch Relay Control Circuit: No Sub Type Information | GO to Pinpoint Test C |
| P06A0:00 | Variable Compressor Control Circuit: No Sub Type Information | GO to Pinpoint Test R |
| P1464:00 | A/C Demand Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test J |
| P193E:00 | A/C Clutch Request Signal: No Sub Type Information | GO to Pinpoint Test N |