Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2022 Ford Police Interceptor Utility and 2022 Ford Explorer. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B108A:01 | Start Button: General Electrical Failure | GO to Pinpoint Test H |
| BCM | B108A:24 | Start Button: Signal Stuck High | GO to Pinpoint Test H |
| BCM | B10F1:14 | Key In Circuit: Circuit Short To Ground or Open | GO to Pinpoint Test G |
| BCM | B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test C |
| BCM | B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test H |
| BCM | B1240:11 | Start Button Mode Indicator: Circuit Short to Ground | GO to Pinpoint Test I |
| BCM | B1240:15 | Start Button Mode Indicator: Circuit Short to Battery or Open | GO to Pinpoint Test J |
| BCM | B1310:12 | Run/Start Control: Circuit Short to Battery | GO to Pinpoint Test C |
| BCM | B1310:12 | Run/Start Control: Circuit Short to Battery | GO to Pinpoint Test H |
| BCM | B1310:14 | Run/Start Control: Circuit Short to Ground or Open | GO to Pinpoint Test C |
| BCM | B1310:14 | Run/Start Control: Circuit Short to Ground or Open | GO to Pinpoint Test H |
| BCM | B1472:12 | Ignition Key Removal Inhibit: Circuit Short To Battery | GO to Pinpoint Test F |
| BCM | B1472:14 | Ignition Key Removal Inhibit: Circuit Short To Ground or Open | GO to Pinpoint Test F |
| BCM | U300A:01 | Ignition Switch: General Electrical Failure | GO to Pinpoint Test L |
| PCM | P2534:00 | Ignition Switch Run/Start Position Circuit Low: No Sub Type Information | For Conventional Ignition Switch: GO to Pinpoint Test D For Push Button Ignition Switch: GO to Pinpoint Test H |
| PCM | P2535:00 | Ignition Switch Run/Start Position Circuit High: No Sub Type Information | For Conventional Ignition Switch: GO to Pinpoint Test D For Push Button Ignition Switch: GO to Pinpoint Test H |
| SCCM | B112B:04 | SCCM: Steering Wheel Module: System Internal Failure | GO to Pinpoint Test Q |
| SCCM | B112B:44 | SCCM: Steering Wheel Module: Data Memory Failure | GO to Pinpoint Test Q |
| SCCM | B112B:45 | SCCM: Steering Wheel Module: Program Memory Failure | GO to Pinpoint Test Q |
| SCCM | B112B:46 | SCCM: Steering Wheel Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test Q |
| SCCM | B112B:49 | SCCM: Steering Wheel Module: Internal Electronic Failure | GO to Pinpoint Test Q |
| SCCM | B135C:11 | Heater Element: Circuit Short To Ground | GO to Pinpoint Test O |
| SCCM | B135C:13 | Heater Element: Circuit Open | GO to Pinpoint Test O |
| SCCM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test P |
| SCCM | U0140:00 | SCCM: Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test R |
| SCCM | U0146:00 | SCCM: Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test R |
| SCCM | U0146:87 | SCCM: Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test R |
| SCCM | U0155:00 | SCCM: Lost Communication With Instrument Panel Cluster Module: No Sub Type Information | GO to Pinpoint Test R |
| SCCM | U023A:00 | SCCM: Lost Communication With Image Processing Module "A": No Sub Type Information | GO to Pinpoint Test R |
| SCCM | U0241:00 | SCCM: Lost Communication With Headlamp Control Module: No Sub Type Information | GO to Pinpoint Test R |
| SCCM | U210A:11 | Temperature Sensor: Circuit Short To Ground | GO to Pinpoint Test O |
| SCCM | U210A:13 | Temperature Sensor: Circuit Open | GO to Pinpoint Test O |
| SCCM | U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test M |
| SCCM | U3003:A3 | Battery Voltage: System Voltage High | GO to Pinpoint Test N |