Specifications Index
COROLLA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 216 N.m (159 ft lbs) | ||
| Rear | 61 N.m (45 ft lbs) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | SERVICE DATA | ||
| Drum Brakes | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | REPLACEMENT | ||
| Belt Routing | REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | 74 to 103 kPa (0.75 to 1.05 kgf/cm2
, 10.7 to 14.9 psi) Minimum 59 kPa (0.6 to 2 , 8.5) |
||
| Thermostat R & I | |||
| (1ZZ-FE) | THERMOSTAT (1ZZ-FE) | ||
| (2ZZ-GE) | THERMOSTAT (2ZZ-GE) | ||
| Water Pump R & I | |||
| (1ZZ-FE) | WATER PUMP ASSY (1ZZ-FE) | ||
| (2ZZ-GE) | WATER PUMP ASSY (2ZZ-GE) | ||
| Engine Mechanical | |||
| (1ZZ-FE) | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | at idle, 29 kPa (0.3 kgf.cm2
, 4.3 psi) or more at 3,000 rpm, 294 to 539 kPa (3.0 to 5.5 kgf.cm2 , 43 to 78 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| (2ZZ-GE) | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | at idle, 39.2 kPa (0.4 kgf.cm2
, 5.7 psi) or more at 3,000 rpm, 245 to 539kPa (3.0 to 5.5 kgf.cm2 , 43 to 78 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate Torque | |||
| Flywheel | 88 N.m (65 ft.Ibf) | ||
| Flex Plate | Step 1: 49 N.m (36 ft.Ibf) Step 2: Turn 90° |
||
| Fuel System | |||
| 1ZZ-FE & 2ZZ-GE | |||
| Pressure Specification | 301 to 343 kPa (3.1 to 3.5 kgf/cm2 , 44 to 50 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 1ZZ-FE & 2ZZ-GE | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug | |||
| IZZ-FE | |||
| Type | DENSO: SK16R11 NGK: 1FR5A11 |
||
| Gap | 1.0 to 1.3 mm (0.039 to 0.051 in.) | ||
| Torque | 25 N.m (255 kgf.cm, 18 ft. lbs) | ||
| 2ZZ-GE | |||
| Type | DENSO: SK20R11 NGK: 1FR6A11 |
||
| Gap | 1.0 to 1.3 mm (0.039 to 0.051 in.) | ||
| Torque | 18 N.m (178 kgf.cm, 13 ft. lbs) | ||
| Starting | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Front | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Rear | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 N.m (1,150 kgf.cm, 76 ft lbs.) | ||