Section 1 (Continuously Variable Transaxle (CVT))
WARNING: This page is about a different variant/trim than selected.
- Service Specifications
- Lubricant
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Initialization Procedure For CVT Learned Value
- CVT Fluid Pressure Control Learning Procedure
- Fluid Deterioration Level Erasing Procedure
- Diagnostic Function
- Freeze Frame Data Reference Table
- Road Test
- Ratio Pattern
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC P0703: Malfunction of Brake Switch
- DTC P0705: Malfunction of Transmission Range Switch
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS (Monitor Sequence-Input Other Rationality)
- LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
- DTC Set Conditions
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- DTC P0711: Malfunction of Transmission Fluid Temperature Sensor
- DTC P0712: Malfunction of the Transmission Fluid Temperature Sensor (Low Voltage)
- DTC P0713: Malfunction of the Transmission Fluid Temperature Sensor (High Voltage)
- DTC P0715: Malfunction of Primary Pulley Speed Sensor
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS [Monitor Sequence-Input Rationality-Low (Open/Low Revolution)]
- LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
- DTC Set Conditions
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- DTC P071B: Malfunction of Ds Position Switch (Stuck ON) DTC P071C: Malfunction of Ds Position Switch (Stuck OFF)
- Diagnostic Function
- Descriptions Of Monitor Methods <P071B>
- Monitor Execution <P071B>
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-Low) <P071B>
- DTC Set Conditions
- OBD-II Drive Cycle Pattern <P071B>
- Descriptions Of Monitor Methods <P071C>
- Monitor Execution <P071C>
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS (Monitor Sequence-Input Rationality-High) <P071C>
- DTC Set Conditions
- OBD-II Drive Cycle Pattern <P071C>
- Probable Causes
- Diagnosis
- DTC P0720: Malfunction of Output Speed Sensor
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS [Monitor Sequence-Input Rationality Low (Open/Low revolution)]
- LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
- DTC Set Conditions
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- DTC P0741: Abnormality in Lockup Function
- DTC P0746: Abnormality in Hydraulic Control System Function
- DTC P0791: Malfunction of Secondary Pulley Speed Sensor
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS [Monitor Sequence-Input Rationality Low (Open/Low Revolution)]
- LOGIC FLOW CHARTS (Monitor Sequence-Input Open Circuit)
- DTC Set Conditions
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- DTC P0796: Abnormality in Primary Pressure Solenoid Valve Function
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS (Monitor Sequence-Output Functional Low)
- LOGIC FLOW CHARTS (Monitor Sequence-Output Functional High)
- DTC Set Conditions
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- Code P0841: Abnormality in Secondary Pressure Sensor Function
- DTC P0842: Malfunction of the Secondary Pressure Sensor (Low Voltage)
- DTC P0843: Malfunction of the Secondary Pressure Sensor (High Voltage)
- DTC P0876: Malfunction of High Clutch Oil Pressure Switch
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution (Stuck On)
- Monitor Execution (Stuck Off)
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS (Monitor Sequence - Stuck ON)
- DTC SET CONDITIONS (Stuck ON)
- LOGIC FLOW CHARTS (Monitor Sequence - Stuck OFF)
- DTC SET CONDITIONS (Stuck OFF)
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- DTC P0962: Malfunction of the Line Pressure Solenoid Valve (Short to Ground)
- DTC P0963: Malfunction of the Line Pressure Solenoid Valve (Open Circuit/Short to Power Supply)
- DTC P0970: Malfunction of the Primary Pressure Solenoid Valve (Short to Ground)
- DTC P0971: Malfunction of the Primary Pressure Solenoid Valve (Open Circuit/Short to Power Supply)
- DTC P0973: Malfunction of the Low Brake Solenoid Valve (Short to Ground)
- DTC P0974: Malfunction of the Low Brake Solenoid Valve (Open Circuit/Short to Power Supply)
- DTC P0976: Malfunction of the High Clutch and Reverse Brake Solenoid Valve (Short to Ground)
- DTC P0977: Malfunction of the High Clutch and Reverse Brake Solenoid Valve (Open Circuit/Short to Power Supply)
- DTC P1607: Malfunction of the System Power Supply (Low Voltage)
- DTC P1637: Malfunction of Memory Backup
- DTC P170E: ASC Error Information
- DTC P1797: G Sensor/Brake Pressure Sensor Malfunction
- Diagnostic Function
- Descriptions Of Monitor Methods
- Monitor Execution
- Monitor Execution Conditions (Other Monitor And Sensor)
- LOGIC FLOW CHARTS (Monitor Sequence - G Sensor Signal Malfunction)
- LOGIC FLOW CHARTS (Monitor Sequence - Brake Pressure Sensor Signal Malfunction)
- DTC Set Conditions
- OBD-II Drive Cycle Pattern
- Probable Causes
- Diagnosis
- DTC P2763: Malfunction of the Lockup Solenoid Valve (Open Circuit/Short to Power Supply)
- DTC P2764: Malfunction of the Lockup Solenoid Valve (Short to Ground)
- DTC P2857: Auxiliary Gearbox Gear 1 Incorrect Ratio Run-up
- DTC P2858: Auxiliary Gearbox Gear 2 Incorrect Ratio Run-up
- DTC P2859: Auxiliary Gearbox Gear 1 Incorrect Ratio
- DTC P285A: Auxiliary Gearbox Gear 2 Incorrect Ratio
- DTC U0001: Malfunction of CAN Communication Circuit (Bus Off)
- DTC U0100: CAN Time-out Error (Engine)
- DTC U0121: CAN Time-out Error (ASC)
- DTC U0141: CAN Time-out Error (ETACS)
- DTC U0155: CAN Time-out Error (Combination Meter)
- Trouble Symptom Diagnosis Chart
- Data List Reference Table
- TCM Terminal Voltage Reference Chart For Transaxle Operation
- Oscilloscope Inspection Procedures
- On-Vehicle Service
- Transaxle Control
- Oil Filter
- Oil Pan And Valve Body Assembly
- Transaxle Assembly
- Transaxle Control Module (TCM)
- Transmission Fluid Cooler Line